RIDGID WD1851 Przewodnik Instalacji

Przeglądaj online lub pobierz Przewodnik Instalacji dla Filtry do aparatów RIDGID WD1851. RIDGID WD1851 Installation Guide Instrukcja obsługi

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj

Podsumowanie treści

Strona 1 - Assemblage

ASSEMBLYAssemblageMontaje

Strona 2

Desempaquetado y comprobación del contenido de la caja de cartón (continuación)OQRNPMClave Descripción Cant.Caja de cartón que contiene las piezas sig

Strona 3 - Contents (continued)

— OR —Threaded StudLidFilterQwik Lock™StudFilterLidPara instalar un filtro nuevo, usted debedeterminar primero qué sistema de sujeción delfiltro se ut

Strona 4

Filter CageQwik Lock™StudFilter Tabs (2)Integrated Filter Plate with Center HolePUSH DOWNPULL UPRubber Gasket at Bottom of Filter (cutaway view)LidRem

Strona 5 - Removal and Installation

NOTE: Smooth side of the wheel to the outside.Caddy LeftDrainAxle w/WheelCaddy RightOpen EndCapNutEnsamblaje del tambor/base de soporteCaddy RightDrai

Strona 6 - Drum/Caddy Assembly

Ensamblaje del tambor/base de soporte (cont.)Instalación del asaOprima y mantenga oprimidos los botones deliberación mientras instala el asa en los re

Strona 7 - Removing Handle

Ensamblaje de la aspiradora para mojado/seco1. Posicione el ensamblaje del cabezal delmotor sobre el ensamblaje del tambor/basede soporte, de la maner

Strona 8 - Wet/Dry Vac Assembly

Se référer au croquis d’assemblage pour lepositionnement des pièces.Retirez tous les éléments se trouvant dans la boîte encarton. Inspectez chaque élé

Strona 9 - Introducción

OQRNPMLégende Description QtéBoîte en carton contenant les pièces suivantes :M Sac de rangement...1N Roue de 8 po...

Strona 10

— OR —Threaded StudLidFilterQwik Lock™StudFilterLidPour installer un nouveau filtre, vous devez d’aborddéterminer quel système de fixation du filtre e

Strona 11

Filter CageQwik Lock™StudFilter Tabs (2)Integrated Filter Plate with Center HolePUSH DOWNPULL UPRubber Gasket at Bottom of Filter (cutaway view)LidRet

Strona 12 - Qwik Lock™

IntroductionThis Wet/Dry Vac is intended for house-hold use. It may be used for vacuumingwet or dry media and may be used as ablower.Refer to the asse

Strona 13

NOTE: Smooth side of the wheel to the outside.Caddy LeftDrainAxle w/WheelCaddy RightOpen EndCapNutCaddy RightDrainCaddy LeftRight Caddy AssemblyLeft C

Strona 14 - Remoción del asa

Assemblage du tambour/chariot (suite)4. Faites glisser l’extrémité libre de l’essieu àtravers le composant gauche du chariot enveillant à ce que la fe

Strona 15 - Introduzca la manguera

Drum LatchDrum LatchDrum FlangeLatchDrumPowerhead AssemblyReleaseButtonPress and PullTote SnapsToteStraps (4)HandleMise en place du porte-outilsInstal

Strona 16 - Introduction

Unpacking and Checking CartonContents (continued)OQRNPMKey Description QtyCarton containing the following parts:M Storage Bag ...

Strona 17

To install a new filter you must firstdetermine which filter attachment systemis used on your Vac.The filter cage has a stud on the end witheither scr

Strona 18

Filter Removal and Installation (con’t.)Removal and Installationof the Qwik Lock™ FilterFilter Removal:1. Hold the filter tabs of the Qwik Lock™filter

Strona 19

3. Installing Cap Nuta. Place cap nut on end of axle.b. Tap gently with hammer until fullyseated.c. Place wheel on the axle with smoothportion of whee

Strona 20

Drum/Caddy Assembly (continued)Installing HandlePress and hold release buttons whileinstalling handle into handle receptaclesin drum (See illustration

Strona 21 - Retrait de la poignée

Wet/Dry Vac Assembly1. Position the powerhead assembly onthe drum/caddy assembly as shown(assembled earlier).2. Rotate both latches down and pressunti

Strona 22 - Mise en place du porte-outils

Consulte el dibujo de ensamblaje paraaveriguar el posicionamiento de las piezas.Saque todo el contenido de la caja de cartón.Asegúrese de que no falte

Komentarze do niniejszej Instrukcji

Brak uwag